VENTOUX ROAD BIKE BOX

£1,044.00 Plus worldwide shipping (free within UK)

*
*

*
*
SKU: 104.001.1 Category:

Description

The big one! Largest capacity and minimal disassembly – there’s not much that won’t fit in this.

For road, gravel, TT and cross bikes. Can be converted for MTB use by switching-out front and rear mounting brackets (available as an accessory).

The only option for outsize bikes and challenging applications such as highly integrated cockpits.

Five minutes to pack/unpack – only requires removal of wheels and seat post (plus aero extensions on TT bikes). Please refer to Which Box? page for further details on maximum bike dimensions.

Compatible with all Thru Axle size standards as well as Quick Release hubs.

Net weight 15kg (33lb). Overall external dimensions 134 x 87 x 36cm (52.6 x 34.2 x 14.2″).

Please note that fork and handlebars must be able to turn through 101 degrees to the right per following image.

Additional information

Front Axle

Quick release, Thru-axle 12×100, Thru-axle 15×100

Rear Axle

Quick release, Thru-axle 12×142

Technical Specification

Weight 15kg (33.2 lb)
Dimensions (LxHxD) 1336 x 869 x 361mm

52.6 x 34.2 x 14.2″

Typical maximum frame size (c-t)*: 635mm (25″)
Suitable for Road, Track, TT & Cross bikes
Disassembly required Wheels, seatpost
Pack/unpack time 5 min/5 min
Latches 4
Handles 4
Wheels 2 fixed, 2 caster
Includes two wheelbags: Yes
Lead-time: typically 2 weeks

(including air-shipment) **

Packing Instructions

Pack/unpack time = five minutes

 

Please also refer to photos above – these show how bike is loaded/attached to box.

1 Prepare bike: Engage top gear. Remove wheels and deflate tyres. Remove seat post.

2 Prepare box: Open box, remove Anti-Crush Bar and wheel bags. Slide Rear Axle Mount to forward-most point on carrier.

3 Place saddle/seat-post under webbing in base of box.

4 For thru-axle bikes, attach Dummy Hubs (castellated aluminium tubes) to front and rear dropouts of bike using the bike’s own thru-axle skewers – note that the chain runs over the top of the Dummy Hub to maintain tension in the chain (not applicable for bikes with QR hubs).

5 Load frame to box. Cranks horizontal, right-hand crank forward.

6a For bikes with thru-axle hubs: Drop front Dummy Hub in to the cradle on Front Axle Mount – secure by inserting Thru-axle Retaining Pin through hole in Front axle mount. Then slide Rear Axle Mount backwards until rear Dummy Hub can be dropped in to Rear Axle Mount – secure with two Thru-axle Retaining Pins. Note: there will be some movement in the Front-Axle Mount – this is accommodate a range of head-tube angles and fork rakes. 

6b For bikes with QR hubs: Insert front dropouts in Front Axle Mount and tighten quick release as you would on the bike (as with a bike, quick release may need adjustment to accommodate lawyer tabs). Manoeuvre rear end of bike such chain is over Rear Axle Mount. Slide Rear Axle Mount backwards to engage with rear dropouts. Tighten quick release as you would on the bike. Note: there will be some movement in the Front-Axle Mount – this is accommodate a range of head-tube angles and fork rakes.

7 Place wheels in wheel bags. Load wheelbags to box, one each side on frame – on right side (looking from rear of box) located forward and on left side located rearward. The slots in the wheelbags should be oriented horizontally and adjacent as shown in photo.

8 Insert Anti-Crush Bar through slots in wheel bag and locate ends in one of three locations in Anti-Crush Retainer (note that you should use same location point on left and right side).

9 Load any other items (e.g. helmet, shoes, track pump) to spare space in box (these should be housed in suitably protective bags to prevent damage during transit).

10 Manoeuvre box lid over box base, taking care to ensure lid is correctly oriented by aligning two green extrusions on front edges. Check that upper and lower edges are positively engaged on all four sides of box.

11 Engage and tighten four latches by turning handle through 90 degrees.

12 If required, secure case by locking the two TSA-approved lock fittings (one on each side of box).

13 You’re all done – safe travels!

Open in WhatsApp
1
💬 Talk to an expert!
Welcome to Buxumbox.
Click to chat to an expert.